Here's the basics: The table measures 31" wide, 63" long, and 34" tall and is made from 2 Kallax shelf units from IKEA, with a desk top surface (also from IKEA) attached to the top. There are also locking wheels underneath to allow me to move the cutting table if I need to.
**This post may contain affiliate links, which means I may receive a small commission (at no additional cost to you) when purchases are made through links found in this post.
The wheels also help to add a little height to the table which makes it a great height for cutting. This table is 34" tall, but if you're tall and need a taller table, you could use legs instead of wheels. IKEA sells legs of various sizes (such as these and these.)
For the table top, you'll need a piece of wood that is at least 31" x 58". We found a desk top at IKEA that had the right measurements but you could also grab something from Home Depot or Lowe's.
edited to add: IKEA has changed the sizes of the desk tops they offer and I believe this size is no longer available. That may change again in the future however.
IKEA sells different inserts to use inside of the cubbies of the Kallax shelf systems. In this photo below you can see that I've added drawers, and one door for some different storage options.
On the opposite side of the table, I use the shelves for books and magazines, and have added some fabric boxes (they come in other colors too - like navy, gray, and black) to store yardage for quilt backs, works in progress, and orphan blocks. They basically work like nice, deep drawers. Other insert options would be these baskets, or these hanging wire baskets.
The large cutting mat on the table is from Quilters Rule and measures 32" x 60" (total size) with grid lines for 28" x 56". The mat was slightly wider than the table so I had my handy brother in law trim about a half an inch off for me with his table saw. I wanted the cutting surface to cover the entire table top, but another option would be to have a cutting surface on half, and an ironing station on the other half of the table! Wouldn't that be handy?
IKEA sells different inserts to use inside of the cubbies of the Kallax shelf systems. In this photo below you can see that I've added drawers, and one door for some different storage options.
On the opposite side of the table, I use the shelves for books and magazines, and have added some fabric boxes (they come in other colors too - like navy, gray, and black) to store yardage for quilt backs, works in progress, and orphan blocks. They basically work like nice, deep drawers. Other insert options would be these baskets, or these hanging wire baskets.
The large cutting mat on the table is from Quilters Rule and measures 32" x 60" (total size) with grid lines for 28" x 56". The mat was slightly wider than the table so I had my handy brother in law trim about a half an inch off for me with his table saw. I wanted the cutting surface to cover the entire table top, but another option would be to have a cutting surface on half, and an ironing station on the other half of the table! Wouldn't that be handy?
This Olfa 24" x 36" mat would work as well, and it would leave a bit of open counter top on one end that would be great for storing rulers or bins/baskets for WIPs! They offer it in blue as well.
edited to add (Sept 2024): I currently use a Creative Grids 28" x 58" cutting mat and it fits great!
I sure love my table! I love how much storage it gives me and how versatile the storage is. I love that I can move it if I need to, and I have needed to move it more than I expected I would. The table a great size for my room - it did feel imposing at first and does take up quite a bit of space, but because of how much storage it gives me I don't know what I'd do without it! If you're limited on space you could make a similar unit using two of these smaller Kallax shelf units.
Now for the details: Want to make your own? Here's what you'll need-
2 Kallax shelf units (IKEA)
1 wood surface / table top (IKEA or Home Depot)
1 sheet of plywood 27" x 54" (Home Depot)
4 swivel locking casters (Home Depot)
2 corner brackets (similar to this one)
2 straight brackets (similar to this one)
screws, bolts and other fasteners
Any inserts you'll need for the Kallax shelf unit (drawers, doors, baskets, etc)
Build the two shelf units. Next, use the 2 straight brackets to bolt the shelf units together. We put the brackets on the inside of the shelves (on the top so it wouldn't get in the way of anything) - one on each end.
You'll build the rest of the table upside down! Place table top, right side down onto the floor. Then place the two joined shelf units upside down onto the table top. Secure in place using the two corner brackets, one on each end.
Next, set the plywood on top of the shelf units (which is actually the bottom) and decide where you'd like the casters. You'll first drill pilot holes for the bolts, and those pilot holes will go through both the plywood and the shelf units. (Our bolts were too long, but I don't mind - I just work around them. You could use bolts that are a shorter length so they don't stick up into the shelf as much.)
Those bolts are what connects the shelf units to the plywood base and helps to stabilize and strengthen the entire unit.
Once the casters are secured, flip the entire shelf unit over and you're ready to start filling it! You can add any Kallax inserts now, or use the cutting table for awhile before deciding just how you want to maximize the storage, and figuring out what works best for you.
Leave any questions in the comments below and I'll do my best to answer them! We did make this cutting table several years ago so we're working from memory on some of these things.
You can read more about how I use the storage in my cutting table in my Sew Organized blog posts:
Sew Organized Part 1: Tips for Storing Quilting Tools and Rulers
Sew Organized Part 2: Tips for Storing Patterns, Magazines, and Books
Sew Organized Part 3: Storing and Organizing Fabric and Scraps
Sew Organized Part 4: Quilting Projects
Now for the details: Want to make your own? Here's what you'll need-
2 Kallax shelf units (IKEA)
1 wood surface / table top (IKEA or Home Depot)
1 sheet of plywood 27" x 54" (Home Depot)
4 swivel locking casters (Home Depot)
2 corner brackets (similar to this one)
2 straight brackets (similar to this one)
screws, bolts and other fasteners
Any inserts you'll need for the Kallax shelf unit (drawers, doors, baskets, etc)
Build the two shelf units. Next, use the 2 straight brackets to bolt the shelf units together. We put the brackets on the inside of the shelves (on the top so it wouldn't get in the way of anything) - one on each end.
You'll build the rest of the table upside down! Place table top, right side down onto the floor. Then place the two joined shelf units upside down onto the table top. Secure in place using the two corner brackets, one on each end.
Next, set the plywood on top of the shelf units (which is actually the bottom) and decide where you'd like the casters. You'll first drill pilot holes for the bolts, and those pilot holes will go through both the plywood and the shelf units. (Our bolts were too long, but I don't mind - I just work around them. You could use bolts that are a shorter length so they don't stick up into the shelf as much.)
Those bolts are what connects the shelf units to the plywood base and helps to stabilize and strengthen the entire unit.
Once the casters are secured, flip the entire shelf unit over and you're ready to start filling it! You can add any Kallax inserts now, or use the cutting table for awhile before deciding just how you want to maximize the storage, and figuring out what works best for you.
Leave any questions in the comments below and I'll do my best to answer them! We did make this cutting table several years ago so we're working from memory on some of these things.
You can read more about how I use the storage in my cutting table in my Sew Organized blog posts:
Sew Organized Part 1: Tips for Storing Quilting Tools and Rulers
Sew Organized Part 2: Tips for Storing Patterns, Magazines, and Books
Sew Organized Part 3: Storing and Organizing Fabric and Scraps
Sew Organized Part 4: Quilting Projects
